Address: 127.127.34.u
Reference ID: WWVB
Driver ID: ULINK
Serial Port: /dev/wwvbu; 9600 bps, 8-bits, no parity
Features: (none)
This driver supports the Ultralink Model 325 (replacement for Model 320) RS-232 powered WWVB receiver. PDF specs available on http://www.ulio.com/. This driver also supports the Model 320, 330,331,332 decoders in both polled or continous time code mode.Leap second and quality are supported. Most of this code is originally from refclock_wwvb.c with thanks. Any mistakes are mine. Any improvements are welcome.
<cr><lf>RQ_1C00LYYYY+DDDUTCS_HH:MM:SSL+5
R = Signal readability indicator, ranging from R1 to R5 Q R1 is unreadable, R5 is best reception
_ = Space
1 = prev. received data bit, values: 0, 1 ,M or ? unknown
C = Signal reception from (C)olorado or (H)awaii 0 = Hours since last WWVB time and flag code update, values 0 00 to 99 (hopefully always 00)
L = HEX A5 if receiver is locked to WWVB, Space if not
YYYY = Year from 2000 to 2099
+ = '+' if current year is a leap year, else ' '
DDD = current day in the year from 1 to 365/366
UTC = timezone (always UTC)
S = Daylight savings indicator, (S)TD, (D)ST, (O) transition into DST, (I) transition out of DST
_ = Space
HH = UTC hour 0 to 23
: = Time delimiter, ':' if synced, Space if not
MM = Minutes of current hour from 0 to 59
: = Time delimiter, ':' if synced, Space if not
SS = Seconds of current minute from 0 to 59
mm = 10's milliseconds of the current second from 00 to 99
L = Leap second pending at end of month, (I)nsert, (D)elete or Space
+5 = UT1 correction, +/- .1 sec increments
Note that Model 325 reports a very similar output like Model 33X series. The driver for this clock is similar to Model 33X behavior. On a unmodified new ULM325 clock, the polling flag (flag1 =1) needs to be set.
<cr><lf>SQRYYYYDDD+HH:MM:SS.mmLT<cr>
S = 'S' -- sync'd in last hour, '0'-'9' - hours x 10 since last update, else '?'
Q = Number of correlating time-frames, from 0 to 5
R = 'R' -- reception in progress,'N' -- Noisy reception, ' ' -- standby mode
YYYY = year from 1990 to 2089
DDD = current day from 1 to 366 + = '+' if current year is a leap year, else ' '
HH = UTC hour 0 to 23
MM = Minutes of current hour from 0 to 59
SS = Seconds of current minute from 0 to 59
mm = 10's milliseconds of the current second from 00 to 99
L = Leap second pending at end of month -- 'I' = insert, 'D'=delete
T = DST <-> STD transition indicators
Note that this driver does not do anything with the T flag. The M320 also has a 'U' command which returns UT1 correction information. It is not used in this driver.
S9+D 00 YYYY+DDDUTCS HH:MM:SSl+5
S = sync indicator S insync N not in sync the sync flag is WWVB decoder sync nothing to do with time being correct
9+ = signal level 0 thru 9+ If over 9 indicated as 9
D = data bit (fun to watch but useless ;-) space
00 = hours since last GOOD WWVB frame sync space
YYYY = current year + = leap year indicator
DDD = day of year
UTC = timezone (always UTC)
S = daylight savings indicator space
HH = hours : = This is the REAL in sync indicator (: = insync)
MM = minutes : = : = in sync ? = NOT in sync
SS = seconds
L = leap second flag
+5 = UT1 correction (sign + digit ))
This driver ignores UT1 correction, DST indicator,Leap year and signal level.
flag1 polling enable (1=poll 0=no poll)